XCPC-9100 CompactPCI PMC Carrier with Eight Port Switch

by tony Losey — last modified 2007-03-27 10:18

Overview

XCPC-9100 is a full hot swap capable mez- zanine carrier board that can hold up to 2 PMC modules with front or rear-panel I/O support in single 6U CompactPCI slot. The XCPC-9100 can accept two PrPMC (PMC processor module) with one configured as Monarch and the other as Non-Monarch. The XCPC-9100 also includes on-board IPMI controller

Using the industry-standard PLX PCI-6540 PCIX-to-PCIX bridge, the XCPC-9100 supports a 32/64-bit data path 33/66 MHz for up to 512 MB/s operation. The two PMC sites support bus mastering and 5V signaling. This carrier has an on-board 8-port Ethernet switch for routing the two channels of PMC Ethernet lines out to PICMG 2.16 and allowing for two Ethernet ports out the front. XCPC-9100 is ideal

Features

6U CompactPCI carrier board with sites for two PMC modules
PMC sites support PrPMC modes, one is Monarch and both can be Non-Monarch
64-bit, 33/66 MHz, up to 512 MB/s operation
Two 10/100/1000Mbps Ethernet ports on the front panel using RJ-45s
On-board 8-port 10/100/1000Mbps Ethernet switch for support of PICMG 2.16
Rear Ethernet ports from PMC modules is routed to on-board switch and provides PICMG 2.16
Full hot swap PICMG 2.1 compliant
On-board IPMI controller
Status LEDs for Power (green) and Hot Swap (blue)
PLX Technology PCIX-to-PCIX Bridge
Supports standard (IEEE1386.1) PMC modules
CompactPCI specification, PICMG 2.0, version 3.0 compliant
Front or Back Panel I/O supports on both PMC sites
128 I/O lines with 16 differential pairs via rear panel J3, J5 CompactPCI connectors
3.3V or 5V PCI signaling for the PMC sites.

CompactPCI Interface

Module can work as the System Controller or as a Peripheral board

PMC Interface

PMC site A will support either Monarch or Non-Monarch PMC processor modules. PMC site B willonly support Non-Monarch PMC processor modules.
3.3 Volt, 5 Volt, +12 Volt and –12 Volt provided for PMC modules via CPCI backplane
Front or rear-panel I/O support for both PMC sites
Interfaces 2 PMC modules in a single 6U CompactPCI slot 32/64-bit, 33/66 MHz, up to 512 MB/s operation

Ethernet support

On-board 8-port Ethernet switch for 10/100/1000Mbps out J3 (PICMG 2.16) and two front Ethernet ports.

Hot Swap Function

“Hot Swap” live insertion and extraction capability (PICMG 2.1 Rev. 2.0 compliant)
Hot swap registers;

- insertion
        - extraction
        - ENUM mask/enable
        - front panel blue LED

IPMI Controller

IPMI “Global” commands
BMC Watchdog timer commands
BMC Device/Messaging commands
Event commands
PEF and Alerting commands
Sensor Device commands
FRU Device commands
SDR Device commands
Sensor suppor

- Voltage
        - Temperature
        - Fans
        - LED
        - Sequencer

Environmental
Form Factor: 6U Compact PCI
Width: 9.2” (233mm) Depth 6.3” (160mm)
Carrier Interface
CompactPCI, PICMG 2.0, version 3.0 compliant

Power Requirements:
+3.3 VDC, 260 mA typical plus any additional power consumed by PMCs
+5 VDC, 100 mA typical plus any additional power consumed by PMCs

Operating Temperature:
0° to 55° C (Air flow requirement as measured with heat sink is to be greater than 200 LFM)

Vibration:
.05Gs RMS (20 - 2000 Hz) random, Operating 6Gs RMS per Hz spectrum
Shock:
30Gs each axis
Storage Temperature:
-25° to 80° C
Relative Humidity:
5 to 95 percent, non-condensing
MTBF:
MIL Spec 217-F@ 105,000 Hrs.

Compliance
IEEE 1386.1 (CMC Standard), VITA 32 (PrPMC Standard). PICMG 2.16, Hot Swap 2.1

Order Information

XCPC-ABC
   A = IPMI Controller
     1 = Installed
     2 = Not Installed
   B = Conformal Coating
     0 = No Coating
     1 = Humiseal 1A33 Polyurethane Conformal Coating
     2 = Humiseal 1B31 Acrylic Conformal Coating
   C= Extended Temperature
     Blank = Standard 0 to 55
   E = Extended Temperature -25 to 70

Download This Page As A PDF

Xembedded, Inc. 710 N. Maple Rd. Saline, MI 48176
Ph. 877.944.1942 Fax 734.944.1999 See us at www.xembedded.com DS_649100_Rev E